hydrostar

[duke401]

i was wondering if enybody has built one of these, i started one back befor xmas an have it almost ready to go execpt for the coil they use a 3.5 inch 1\2 inch thick with a 2 inch hole in the middle [ looks like a donut] magnut with 550foot of 23 ga. mag. wire rapped though an around it. my ? is how much good would the coil do. i have the tubing built mine is just a 1.5 inch pipe with a smaller one inside. all i did with it was hook it strait to a 12 volt battery. i have 3\8 pipe fitting an i could feal pressure almost instint, but i dont have the coil inthere. i can have the coils built in calf. but had to buy 3 at 500 to get started. after that i vered towards cris`s design. now i was woundering if enybody knows where a person can get a coil like that. might as well finsh it an see what happens.
duke

[russ]

The Hydro* construction manual has a few proofreading errors. The electromagnet to be inserted into plastic pipe casing needs to have an external magnetic field. The parts list calls for a PN which is made of ferrite, for high frequency. (A full toroid coil has no outside magnetic field. )What is needed is a powdered iorn toroid core 3" OD 1.9" ID and 1/2" thick. Frequency used is a low 20 cycles approx. Clamp it between two boards and grind in a wide slot through the thickness, and hand file smooth edges. This way a pulsing magnetic field is there exterior to coil because the flux does not have a continuous round path. With about 500 feet of #22-#23, you get about 8 ohms. So that at 12 volts you get about an amp current with very high turns, and magnetic field. The slot also allows much easier hand winding and can click a counter on the side. There are about 3 grades of iron cores for flux density depending on money spent. The overall outer OD of wired coil has to fit loosely inside casing . PVC is 4"ID, CPVC pipe is about 3.75" ID. The Hydrostar is similar to the design by Xogen, Meyer, and Dan Danforth hydrogen generator. My opinion is that the coil should have 2 uses at the same time. When transister Q shuts off , the coil reverse high volts pulse should be hooked to one end plate of water capacitor cell. With tap water, there is about 2 ohms resistance, so that a very high value resistor would be attatched between opposite electrode and ground. The applied stress should aid the process making fuel gases. Electron flow from neg to pos, then reverse collapse of magnetic field. High voltage one way blocking diode protects lower transister. Regular heavy coated magnet wire is cheaper than teflon coated wire. The teflon insulation makes a wider overall coil, due the the thick teflon coating. May not get required 1500 turns teflon to fit, and the center hole gets smaller.

WWW.CWSCoils.COM
internet sales catalog for toroids
PN T300-26 $5.00 + shipping iron powder
PN CH77125 $15 + shipping High Flux density
PN CS777125 $8.75 + shipping sendust alloy

[rcfinatic]

[duke401]

yes i would say that it was a a take off the hydro* plan. the real hydro* plan is 94 pages long. hope to get every thing set up tomorrow to run a 5 hp briggs i am keepen my fingures crossed [that might help for getting them blown off ]
what little i have done i think i am getting more h2 with the tube inside a tube instead of plates.
duke

[duke401]

russ i couldnt get to the sales catalog i would like to play with some if i could get my hands on some
thanks
duke

[russ]

The three inch iron powder toroid which needs a gap sawed into it, can be purchased on line from http://www.coilws.com
An electric click (noise) counter can be mounted next to the core and magnet wire for counting turns up to 1500. Splice in a microswitch with long extention for hand passing by for each turn.

[importfanatik]

[mrgalleria]

Aloha,
I was contacted by the people promoting hydro* on e bay. They had seen the plans I listed for the nitrogen based booster. They were rather bold (I think it was a lady named Kathey) telling me to get "all my marbles in a row", and saying lots of people were running cars on water alone using hydro*. I asked her to send me a photo of her car running on water but never heard from her again.
Bill

[Bob Boyce]

Aloha Bill

I wouldn't worry too much about them. They bought the marketing rights to the hydro* device, and are only trying to make money. They don't give a rats ass about whether it works or not. They just get upset when others give away information that they claim are "trade secrets" or "proprietary technology" for free. Apparently, they think that since they own the marketing rights for that device, it entitles them to be the exclusive outlet for ALL booster technology information. Me and my lawyer do not agree!

Everyone here, I would be very careful about typing the entire name in your post text, they may come after you for use of their trademark without express written permission, or some such nonsense. They do not tolerate bad publicity well, and will do almost anything to keep people from finding out the truth. Take it from experience.

Bob

[Bart West-VL.]

[importfanatik]

[mrgalleria]

[Bob Boyce]

[orang_pulau]

G'day,
I am gonna build one of these with my old man, but I didn't have to pay for the plans...I found them here: http://www.web-space.tv/free-energy/ God bless the Internet, It can be useful in the utmost. Just click down the bottom of the first page to pop up its in German "Bitte kliken zie hier..." Or some such. The plans can be found down the bottom again of the next page and are labled "File 20; ...vehicle modification manuals"

I would like to get this thing running, so if anyone else wants to collaborate or has any information needed to get these things to work then please let me know. We need to all work together to get the information out there!!! We need to be able to stop relying on our respective governments. Sure, vote for 'em and pray for 'em but don't rely on them...

Blessings