oh by the way this is at 12v and 15 amps and after about 30 min of continuous running
hot terminals
18 posts
• Page 1 of 2 • 1, 2
hot terminals
by hydroxrox » Fri Jul 04, 2008 4:23 pm
so my terminals on the top of my cell get pretty hot below on the left is my current design and on the right is an idea to help with the heat on the terminals let me know what you think.
oh by the way this is at 12v and 15 amps and after about 30 min of continuous running
oh by the way this is at 12v and 15 amps and after about 30 min of continuous running
Hydrox Rox Sox
- hydroxrox
- Regular Poster
- Posts: 92
- Joined: Tue Dec 25, 2007 3:38 pm
- Location: utah
Low Voltage configuration
by SeaMonkey » Fri Jul 04, 2008 8:35 pm
-
SeaMonkey - Regular Poster
- Posts: 396
- Joined: Thu Aug 09, 2007 4:00 pm
- Location: Dystopia, USSA
by hydroxrox » Fri Jul 04, 2008 8:50 pm
sea monkey, dude seriously you F*** rock!:D you are always there when some newb needs help, it is appreciated!
i actually have a pulser ordered from pwmpower.com and i have had issues finding a good dc to dc converter
but on another note i am making 1.5 liters a minute now and all i did was mess with the plate spacing, man that helped a ton.
Edited out profane language. Looking In
i actually have a pulser ordered from pwmpower.com and i have had issues finding a good dc to dc converter
but on another note i am making 1.5 liters a minute now and all i did was mess with the plate spacing, man that helped a ton.
Edited out profane language. Looking In
Hydrox Rox Sox
- hydroxrox
- Regular Poster
- Posts: 92
- Joined: Tue Dec 25, 2007 3:38 pm
- Location: utah
by Looking In » Thu Jul 10, 2008 7:38 am
hydroxrox,
It looks to me you are running 16 plates now. How big are the plates?
It looks to me you are running 16 plates now. How big are the plates?
Rich (Looking In)
((((Is it really so difficult to tell a good action from a bad one? I think one usually knows right away or a moment afterward, in a flash of regret.)))) BOOM
((((Is it really so difficult to tell a good action from a bad one? I think one usually knows right away or a moment afterward, in a flash of regret.)))) BOOM
- Looking In
- Regular Poster
- Posts: 367
- Joined: Thu Dec 22, 2005 11:06 am
by FlashBang » Thu Jul 10, 2008 9:48 am
OK... this brings up a critical point... For a given low voltage cell, what is the optimum number of plates or square inches of reactive surface area? For example... If I have a 4 inch pipe... and I can fit 20 plates 12x2.5.... in a LVC...Is it better to put all 20 in one electrolyzer tank oe split into two with 10 plates each?
There has been a lot of experimentation and these types of cells.... We should be able to make some OPTIMAL perfromance specs, so that the next round of experiments can start there with the benefit of that accumulated knowledge.
Just my thoughts.
FlashBang!
There has been a lot of experimentation and these types of cells.... We should be able to make some OPTIMAL perfromance specs, so that the next round of experiments can start there with the benefit of that accumulated knowledge.
Just my thoughts.
FlashBang!
Just becuase you are Paranoid doesn't mean that they are NOT out to get you!
- FlashBang
- Regular Poster
- Posts: 270
- Joined: Sun Jun 01, 2008 10:58 pm
- Location: Florida
Number of plates in a cell
by SeaMonkey » Thu Jul 10, 2008 10:04 pm
-
SeaMonkey - Regular Poster
- Posts: 396
- Joined: Thu Aug 09, 2007 4:00 pm
- Location: Dystopia, USSA
by mrgalleria » Mon Jul 14, 2008 5:27 am
-
mrgalleria - Regular Poster
- Posts: 358
- Joined: Sat Dec 03, 2005 4:52 am
- Location: Big Island, Hawaii
by mrgalleria » Mon Jul 14, 2008 6:53 am
-
mrgalleria - Regular Poster
- Posts: 358
- Joined: Sat Dec 03, 2005 4:52 am
- Location: Big Island, Hawaii
18 posts
• Page 1 of 2 • 1, 2
Return to Hydrogen Production via Electrolysis
Who is online
Users browsing this forum: No registered users and 14 guests