shaft for about 15mm each end.
Material is 316 stainless, and will be fully roughed out before letting to settle
before finish machining and "polishing" into tolerance.
How would I go about calculating the growth on diameter per degree C?
Statistics: Posted by Simeon — Fri Nov 11, 2011 2:10 am
]]>
While driving car for the first time I seem to have trouble to put on 3. Put is just me trying to shift like before. I forced it in 1 instead of putting it on 3!!! It obviously made a loud motor noise. But quickly put it back to neutral, then 2 again.
Took me a good 2 or 3 doing, it that way before realizing new transmission means differently shifting.
I am wondering, did I ruin the motor or something else by wrongly shifting to first gear? RMP just feels strange, as need to shift earlier in the RPM than before. While I was driving at stable seep, I saw the RPM arrow, like slightly going down.
What could it be? Or there’s a adjustment to be done with new transmission?
Statistics: Posted by Simeon — Fri Nov 11, 2011 2:08 am
]]>
]]>
]]>
http://www.youtube.com/watch?v=nbYDkDo3dco
... The darn thing stops???
Statistics: Posted by mael — Sun May 09, 2010 2:03 pm
]]>
Note to self; Buy some magnets to play with
Statistics: Posted by Jehu — Sat May 08, 2010 9:53 am
]]>
]]>
Like this:-
http://www.youtube.com/watch?v=n-fnlmzj ... re=related
... I envisioned having a series of steps of these 'V' gates moving the steel ball. The idea is new to me, and I'm just airing my thoughts. I thought that the ball would run along (and upwards at an incline) a rail.
One other thing I spotted was a magnetic-rail version of 'worry-beads,' which would have the balls knocking the next one along the line, and the final one would be sent out to roll onto the wheel.
... I'll find a video.
Statistics: Posted by mael — Fri May 07, 2010 2:46 pm
]]>
From what I've seen, alot, actually, make that all the magnetic OU devices have the old gating problem where the moving part gets stuck by the magnetic fields at the end of the array/accelerator. I think the idea with that is shielding/guiding of the the flux lines so to stop this effect. Most people go about it in the wrong way from how I see it though.
Statistics: Posted by Jehu — Fri May 07, 2010 9:48 am
]]>
Statistics: Posted by mael — Fri May 07, 2010 9:40 am
]]>
]]>
* Accelerated itz. - ie. not acellerated.
Statistics: Posted by mael — Fri May 07, 2010 8:53 am
]]>
The most successful method I find is me going to the moon and with a few rudimentary tools and supplies, I work against time to build my first 'room' in the side of a crater (hill), and the idea is that I continue and make a growing room, a kitchen etc... . But I don't usually get much farther than drilling-in studs to hold the first door in place - because I'm usually asleep by that stage.
But last night I was troubled by something and I kept thinking about it and didn't sleep till late.
I think about ways to get a few Watts c/o nature all through the day, and also at night - especially when it's quiet and there are otherwise no distractions. The usual ones are the wind and water ... neither are practical in the workshop I 'live' in. - So I think of other ways to get power and would like to discover a way for me to switch the mains breaker switch to 'off,' and run everything from something I can create.
Blah blah blah ...
Ahem! 
The Bessler's wheel idea is a fairly new one to me. But last night I figured it out. Maybe it's not the wheell he created or envisioned, but it's a wheel which continually turns and needs no energy input. It will certainly have energy left over to drive a generator, and the amount of excess power depends on the size of the thing.
It's something I could make and then watch it work - forever.
So I'll tell you:-
It's a wheel - like a bicycle wheel. It's rotated by the unbalancing effect of a steel ball (or plural steel balls). The steel balls would be fed somewhere near the top, and would exit at the bottom.
Where the balls exit, they will be guided to a permanent magnet "rail-gun" (of sorts).
Basically, the steel balls are acellerated and effectively returned to the top of the wheel and then rotate the wheel on their way down, where the cycle begins again.
* Of course one needs to be clever with the design of the 'rail-gun,' but I can see no reason why this would not work.
* Tonight I'm going to grab some washing machine motors and liberate the powerful magnets inside them and I'm hoping I can knock something up (I mean a device
) which will prove the concept.I can't edit here, so I'll add a link of the magnetic acellerator I have in mind for the task of raising the steel balls to the height of the wheel.
Nah! I don't want to make money out of it. I just want people to free of ZOG.
And where's that video? Gdi just share your ideas and let's get ourselves free of the Banksters.
Statistics: Posted by mael — Fri May 07, 2010 8:43 am
]]>
aussepom
Statistics: Posted by aussepom — Tue Feb 16, 2010 2:26 am
]]>
Bill
Statistics: Posted by mrgalleria — Thu Dec 31, 2009 1:58 am
]]>