Hi Aussie pom,
Firstly the ecm are very sophisticated management tools. The have adoptive learning and you can normally buy a programmer for them relatively cheaply. Most service technitians I know dont rip you off.
With a programmer you can doanything and increase fuel milage by at least 10% and add some horsepower.
If you want to run an engine just on hydrogen or hydroxy you basically need a specifically designed engine. Boosting an engine with some gas is ok however you will run into a host of other problems, mainly metalurgy. You will becertainly able to run any engineon hydroxy...no doubt but it will not last very long.
Most manufacturers have engines built for Hydrogen now...some you can purchase already. In my research I will be using an older engine for proof of concept when I test for gas/HP ratio.
Will be interesting to get the new results from the engine test...make sure its loaded and its important to always be acurate and factual when reporting results otherwise many people can be misled.
Kind Regards
Mark
Thinking outside the Box
17 posts
• Page 1 of 2 • 1, 2
Hey Mark, I won't be able to work on this for about 2 months
by savage1r » Sun May 27, 2007 12:36 pm
- savage1r
- Regular Poster
- Posts: 32
- Joined: Fri May 11, 2007 2:48 am
by MarkinAustralia » Tue May 29, 2007 11:13 pm
Hi Glenn,
I am very homesick fro family and Australia.
The cell was 4 sealed cells of 7 plates about 5" x8".
We have cranked out 3 litres a minute out of the single cells.
I dont intend to try at this stage to increase cell efficency...but I am looking at different ways of powering them.
Follow Bob's rules re amps surface area etc.
I have been priveledge to see inside and know the performance of many of the big players. All I can say I have seen none better than Fradays.
I will be ordering a commercial 50 or 100 litre a minutegas generator this week to do some tests.
I have taken a different aproach to increasing efficiency...better alternators and utilizing waste energy. Will see whta results I get.
One thing I will do is post how many litre per minute we need per HP with hydroxy. This will give us something to aim for when increasing efficency.
Bob has been very helpful and I thank him
Also email me Alaska as I have a new phone. I am in Oregon (Hope I spelt that right)
Anyone thinks of some other tests they want me to run let me know.
Tale Care
Mark
I am very homesick fro family and Australia.
The cell was 4 sealed cells of 7 plates about 5" x8".
We have cranked out 3 litres a minute out of the single cells.
I dont intend to try at this stage to increase cell efficency...but I am looking at different ways of powering them.
Follow Bob's rules re amps surface area etc.
I have been priveledge to see inside and know the performance of many of the big players. All I can say I have seen none better than Fradays.
I will be ordering a commercial 50 or 100 litre a minutegas generator this week to do some tests.
I have taken a different aproach to increasing efficiency...better alternators and utilizing waste energy. Will see whta results I get.
One thing I will do is post how many litre per minute we need per HP with hydroxy. This will give us something to aim for when increasing efficency.
Bob has been very helpful and I thank him
Also email me Alaska as I have a new phone. I am in Oregon (Hope I spelt that right)
Anyone thinks of some other tests they want me to run let me know.
Tale Care
Mark
Follow your passion
- MarkinAustralia
- Regular Poster
- Posts: 262
- Joined: Sat Jul 15, 2006 8:48 am
- Location: Australia
17 posts
• Page 1 of 2 • 1, 2
Return to Hydrogen Production via Electrolysis
Who is online
Users browsing this forum: No registered users and 36 guests