Welcome to OUPower.com
"Over Unity Power" Research

kettle c.2003 Project Page 4

This Website is Created and Maintained by chris--at--OUPower--dot--com (Fix the address for it to work!)
This Project was last updated on: September 25, 2006 10:37am v7.01

WARNING! Many, if not all of the projects described within these pages, contain dangerous and potentially fatal consequences if you do not exercise proper precautions and follow standard safety procedures. The owner of this site takes no responsibility for injury sustained by anyone attempting to duplicate or utilize any of the information on this site. The information here is strictly for Educational Purposes! -USE AT YOUR OWN RISK!

Click Here to go to my YouTube Channel!!

Click Here to go to our NEW Facebook Discussion Group! This is replacing the old Discussion Board!

Click Here to go to our ARCHIVED Discussion Boards.

Please consider donating to help support this website!

Click here to continue Drilling into Projects from AntDavison

Click Here to Re-Display the Main Project Page
Project Description:
leave a message for me at http://oupower.com/phpBB2/viewtopic.php?t=358

my 4 plate kettle ... made in 2002 and the controller in 2003 before i knew about the 2v water thing, so should work well of an old 5v mainframe 5v/100A computer power supply with only two of the plates wired ... will run warm off 12v/14v.

was always to scared to ignite its output, but have filled lots of balloons with it with 2 minute dynamite fuses  and blown them up which is fun (i go to my friends farm ... he has a dynamite licence)

if i were to follow chris' thinking, i should build another 5 or 6 cells, and wire the 4 plates as two parallel pairs

the elctronics (my first successful electronics project) evolved after i tried replicating the "spirit ot ma'at" circuit diagrams which didn't work for me ... i made a mosfet version but the mosfets kept melting, so i had to go for the most indestructable mosfet (150A continuous) i could find ... so all a bit of a learning curve

my background; 13yrs schooling; 5 years university (law degree + 2/3 arts; mainly in social history), working part time in an autoelectricians (cleaner boy, rebuilding starters, generators, alternators)  and in a speaker factory; then working full time as a technical assistant to a couple of firms of patent attorneys for 4 years, qualified as an attorney; 1988 stock market crashed caused career change to computer animation with an artist friend, specializing in 3D.cg tv commerials, now working for national television broadcaster looking after 30 computer artists

Proceed to another page of the kettle c.2003 Project: [<<<   <      >   >>>]

early tests, no electrolyte skinny little wires

looking closer

finished assembly has a diameter of  108mm + the height of two nuts, totalling around 125mm or 5"

need to handle the assembly carefully so you dont deform the plates, you don't want one plate touching another, so test that they are electrically isolated from one another

mount in a container that is hard to squeeze

nice side view

those lower nylon and brass nuts DO get replaced with stainless steel ones

marine chandlers have lots of stainless hardware and fittings

early trial with water from a hot water cylinder turned it a copper orange colour within 10 seconds, i had also tried water from a mountain stream, its still the colour of yellow urine 3 years later, with black minerals at the bottom of the container

Proceed to another page of the kettle c.2003 Project: [<<<   <      >   >>>]

Click here to continue Drilling into Projects from AntDavison

Click Here to Re-Display the Main Project Page

This Website is Created and Maintained by chris--at--OUPower--dot--com (Fix the address for it to work!)
This Project was last updated on: September 25, 2006 10:37am v7.01

WARNING! Many, if not all of the projects described within these pages, contain dangerous and potentially fatal consequences if you do not exercise proper precautions and follow standard safety procedures. The owner of this site takes no responsibility for injury sustained by anyone attempting to duplicate or utilize any of the information on this site. The information here is strictly for Educational Purposes! -USE AT YOUR OWN RISK!

Click Here to go to my YouTube Channel!!

Click Here to go to our NEW Facebook Discussion Group! This is replacing the old Discussion Board!

Click Here to go to our ARCHIVED Discussion Boards.

Please consider donating to help support this website!